User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: PM 2524 Verfication Proceedure (Ver1.4) DATE: 03-Oct-93 AUTHOR: User Contributed REVISION: 1.4 ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 37 NUMBER OF LINES: 91 CONFIGURATION: Fluke 5700A ============================================================================= * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Source: Service Manual PM P/N: @ * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * TUR Configuration: * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * When the T.U.R. is < 2:1, the source instrument, e.g. 5700A, must be * characterized and appropriate corrections entered in the correction file * (e.g. 5700.COR). Where T.U.R.'s are > 2:1 but < 4:1, the test tolerance * is reduced by root sum square (rss) techniques. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * This procedure is not executable in MET/CAL versions below ver. 2.00 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Fluke make no warranty, expressed or implied, as to the fitness or * useability of this procedure. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Main Procedure TESTS: Verification * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * The following subprocedures are called from this main procedure: * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 DRAW 7 78 7 78 75 5 50 55 1.002 DISP Turn POWER on. [DRAW10,5,F] 1.003 DISP Allow the UUT to warm up for 30 min. and proceed the 1.003 DISP test at an ambient temp. of 23 +/- 1 deg. Celsius. 1.004 ASK- R 1.005 DISP Shortcircuit the 0 and the V-Ohm terminals to check 1.005 DISP the zero point (000.00 mV +/- 1 digit). 1.005 DISP Readjust the zero point if necessary 1.006 DISP Remove the shortcircuit, and connect testleads to the 1.006 DISP 0 and the V-Ohm terminals. 1.007 HEAD {DC VOLTAGE TEST} 1.008 5700 200 190mV 0.005/ 0.02% 2W 2.001 5700 200 -190mV 0.005/ 0.02% 2W 3.001 5700 2 1.9V 0.005/ 0.02% 2W 4.001 5700 2 -1.9V 0.005/ 0.02% 2W 5.001 5700 20 19V 0.005/ 0.02% 2W 6.001 5700 20 -19V 0.005/ 0.02% 2W 7.001 5700 200 190V 0.005/ 0.02% 2W 8.001 5700 200 -190V 0.005/ 0.02% 2W 9.001 5700 2000 1000V 0.005/ 0.02% 2W 10.001 5700 2000 -1000V 0.005/ 0.02% 2W 11.001 HEAD {AC VOLTAGE TEST} 11.002 DISP Set PM2524 in Vac range. 11.003 5700 200 190mV 0.1/ 0.2% 60H 2W 12.001 5700 200 190mV 0.2/ 0.5% 30kH 2W 13.001 5700 2 1.9V 0.1/ 0.2% 60H 2W 14.001 5700 2 1.9V 0.2/ 0.5% 30kH 2W 15.001 5700 20 19V 0.1/ 0.2% 60H 2W 16.001 5700 20 19V 0.2/ 0.5% 30kH 2W 17.001 5700 200 190V 0.1/ 0.2% 60H 2W 18.001 5700 200 190V 0.2/ 0.5% 30kH 2W 19.001 5700 2000 500V 0.1/ 0.2% 50H 2W 20.001 5700 2000 500V 0.1/ 0.2% 1kH 2W 21.001 HEAD {DIRECT CURRENT TEST} 21.002 DISP Disconnect testlead from V-Ohm terminal and connect 21.003 DISP it to the Ampere terminal. 21.004 DISP Set PM2524 in IDC range. 21.005 5700 2000 1.9mA 0.005/ 0.2% 2W 22.001 5700 2000 -1.9mA 0.005/ 0.2% 2W 23.001 5700 2000 19mA 0.005/ 0.2% 2W 24.001 5700 2000 -19mA 0.005/ 0.2% 2W 25.001 5700 2000 190mA 0.005/ 0.2% 2W 26.001 5700 2000 -190mA 0.005/ 0.2% 2W 27.001 5700 2 1.9A 0.005/ 0.2% 2W 28.001 5700 2 -1.9A 0.005/ 0.2% 2W 29.001 HEAD {ALTERNATING CURRENT TEST} 29.002 DISP Set PM2524 in IAC range. 29.003 5700 2 1.9A 0.005/ 0.2% 100H 2W 30.001 5700 200 190mA 0.005/ 0.2% 100H 2W 31.001 DISP Disconnect testlead from Ampere terminal and connect 31.001 DISP it to the V-Ohm terminal. 31.002 HEAD {RESISTANCE TEST} 31.003 DISP Set PM2524 in Ohm range. 31.004 5700 200 190Z 0.005/ 0.3% 2W 32.001 5700 2 1.9kZ 0.005/ 0.3% 2W 33.001 5700 20 19kZ 0.005/ 0.3% 2W 34.001 5700 200 190kZ 0.005/ 0.3% 2W 35.001 5700 2 1.9MZ 0.005/ 0.3% 2W 36.001 5700 20 19MZ 0.005/ 1% 2W 37.001 END